ABB Module SAMC19INF SAMC 19 INF 57401389 ABB SAMC19INF SAMC STROMBERG reputation based

ABB Module SAMC19INF SAMC 19 INF 57401389 ABB SAMC19INF SAMC STROMBERG reputation based

Product Description:

When resistance thermometers are used, a constant current must flow through the measuring resistor in order to create the necessary voltage drop for the evaluation. For this purpose, the basic unit 07 KT 94 provides a constant current sink, which is multiplexed to the 8 analog channels. The following figure shows the connection of Pt100 resistance thermometers in 2-wire configuration.Measuring ranges and with Pt100 as temperature sensor in 3-wire configuration The following figure shows the connection of Pt100 resistance thermometers in 3-wire configuration.The 07 KT 94 unit linearizes the Pt100 characteristic.Temperatures that exceed the measuring range cause the overflow numerical value of +32767. If the measured value is below the range, the underflow numerical value of -32767 is set. In case of a detected open-circuit the numerical value of +32767 is set. If the sensor is short-circuited, the numerical value of -32767 is set.

Related Product Recommendation:

Product's Character:

In order to avoid measurement errors, it is absolutely necessary, to lead the cores to the Pt100 sensors in the same cable. The cores must have the same cross section. Per channel, a twisted pair is used (for the two terminals of the Pt100 sensors) plus a single core (half of a twisted pair) for the connection to AGND1. Depending on the configured operating mode, the measured value is assigned linearly as follows the return wire AGND1. In the operating mode "Pt100 in 3-wire configuration" two adjacent analog inputs belong together (e.g. EW 6,00 and EW 6,01). For configuration, both inputs must be configured to the desired operating mode, see configuration table Fig. The constant current of the one channel flows through the Pt100 resistance sensor, the constant current of the other channel through one of the wires.
The basic unit 07 KT 94 calculates the measuring value from the two voltage drops and stores it under the odd address

AO845 3BSE023676R1 Redundant Analog Output Module ABB
AO845A 3BSE045584R1 Redundant Analog Output Module ABB
AO890 3BSC690072R1 Analog Output Module ABB
AO895 3BSC690087R1 Analog Output Module ABB
AO910N 3KDE175533L9100 Analog Output Module ABB
AO930S Analog Output AO930S ABB
AOT-150 PHBAOT15010000 AOT 150 Analog Output Module ABB
AP5524a HTGR 414729 R1, HTGR414729R0001 AP5524a Module ABB
APSAF03 E32086 Safety Board ABB
AT 5513a HEIA404921R1, HEIA404921R0001 AT5513a Module ABB
AV 02 0776011B H&B Contronic AV 02 Module ABB
AV 06 0776005F, 66023-2-0000 H&B AV 06 Contronic Module ABB
AV 07 AV07 H&B AV 07 Contronic Module ABB
AV 08 66011-4-0776007, H&B Contronic AV 08 module ABB
AV 31 0776009D H&B Contronic AV 31 (AV31) Module ABB
AV 41 0776013J H&B Contronic AV 41 Module ABB
AV 42 0776014K H&B Contronic AV 42 Module ABB
AV 43 0776019A H&B Contronic AV 43 (AV43) Module ABB
AV 98 0775909C H&B Contronic AV 98 Module ABB
AW 01 66028-2-0000 H&B Contronic AW 01 Module ABB
AW 02 0776002F H&B Contronic AW 02 Module ABB
AW 03 0776010F, 66025-2-0000 H&B Contronic AW 03 Module ABB
AW 05 0776011B H&B Contronic AW 05 Module ABB
AX210 492953301 Analog Input/Output Module ABB
AX670 3BSE000566R1 Analog Mixed Module ABB
B-5MP9I-A0002 IIATB05 MouseTRAK Trackball ABB
B-5MPBC IIATB05 MouseTRAK Trackball ABB
B6-30-01 Contactor ABB
B6-30-10 Mini Contactor Module ABB
B6-40-00 Contactor ABB

BC810 3BSE030230R1 CEX-Bus Interconnection Unit, ABB
BC810K01 3BSE031154R1 BC810 CEX-Bus Interconnection Unit Kit ABB
BC810K02 3BSE031155R1 CEX-Bus Unit ABB
BRC-100 P-HC-BRC-10000000 BRC100 Harmony Bridge Controller ABB
BRC300 PHCBRC30000000 BRC300 Bridge Controller ABB
BRC400 PHCBRC40000000 BRC400 Bridge Controller ABB

The use of the product: