Allen Bradley Modules 1768-M04SE 1768 M04SE AB 1768M04SE Ser ASercos 4 Axis Interface Free shipping

Allen Bradley Modules 1768-M04SE 1768 M04SE AB 1768M04SE Ser ASercos 4 Axis Interface Free shipping

Product Description:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

Related Product Recommendation:

Product's Character:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

1746-IV32 Current Sourcing DC Input Module AB
1746-IV8 Current Sourcing DC Input Module AB
1746-N2 Card Slot Filler AB
1746-NI16I High Resolution Analog Input Module - Current AB
1746-NI16V High Resolution Analog Input Module - Voltage AB
1746-NI4 High Resolution Analog Input Module AB
1746-NI8 High Resolution Analog Input Module AB
1746-NIO4I High Resolution Analog Input/Output Module AB
1746-NIO4V High Resolution Analog Input/Output Module AB
1746-NO4I Analog Current Output Module AB
1746-NO4V Analog Voltage Output Module AB
1746-NO8I Analog Current Output Module AB
1746-NO8V Analog Voltage Output Module AB
1746-NR4 RTD Input Module AB
1746-NR8 RTD Input Module AB
1746-NT4 Thermocouple Input Module AB
1746-NT8 Thermocouple Input Module AB
1746-OA16 120/240V AC Output Module AB
1746-OA8 120/240V AC Output Module AB

1746-OAP12 High Current 120/240V AC Output Module AB
1746-OB16 Current Sourcing DC Output Module AB
1746-OB16E Isolated Sourcing DC Output Module AB
1746-OB32 Current Sourcing DC Output Module AB
1746-OB32E Isolated Sourcing DC Output Module AB
1746-OB6EI Isolated Sourcing DC Output Module AB
1746-OB8 Current Sourcing DC Output Module AB
1746-OBP16 High Current Sourcing DC Output Module AB
1746-OBP8 High Current Sourcing DC Output Module AB
1746-OG16 Current Sinking TTL Output Module AB
1746-OV16 Current Sinking DC Output Module AB
1746-OV32 Current Sinking DC Output Module AB
1746-OV8 Current Sinking DC Output Module AB
1746-OVP16 High Current Sinking DC Output Module AB

The use of the product: