Allen Bradley Modules 1771-IL 1771 IL AB 1771IL Analog Current/Voltage Input Highest version

Allen Bradley Modules 1771-IL 1771 IL AB 1771IL Analog Current/Voltage Input Highest version

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Related Product Recommendation:

Product's Character:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

1746-OAP12 High Current 120/240V AC Output Module AB
1746-OB16 Current Sourcing DC Output Module AB
1746-OB16E Isolated Sourcing DC Output Module AB
1746-OB32 Current Sourcing DC Output Module AB
1746-OB32E Isolated Sourcing DC Output Module AB
1746-OB6EI Isolated Sourcing DC Output Module AB
1746-OB8 Current Sourcing DC Output Module AB
1746-OBP16 High Current Sourcing DC Output Module AB
1746-OBP8 High Current Sourcing DC Output Module AB
1746-OG16 Current Sinking TTL Output Module AB
1746-OV16 Current Sinking DC Output Module AB
1746-OV32 Current Sinking DC Output Module AB
1746-OV8 Current Sinking DC Output Module AB
1746-OVP16 High Current Sinking DC Output Module AB
1746-OW16 Relay Output Modle AB
1746-OW4 Relay Output Modle AB
1746-OW8 Relay Output Modle AB
1746-OX8 Relay Output Modle AB
1746-P1 Power Supply Module AB
1746-P2 Power Supply Module AB
1746-P3 Power Supply Module -DC AB
1746-P4 Power Supply Module AB
1746-P5 Power Supply Module -DC AB
1746-P6 Power Supply Module -DC AB
1746-P7 Power Supply Module -DC AB
1746-QS Synchronized Axes Module AB
1746-QV Open-Loop Velocity Module AB
1746-SIM Input Simulator AB
1746SC-INI4I Analog Current Input Module Spectrum Controls
1746SC-INO4I Analog Current Output Module Spectrum Controls

Nikon 4S018-402 Circuit Board MTH-8SH working

Nikon 2S700-323-2 PCB Circuit Board 2S020-020-5 Used Working

Nikon 2S701-009 PCB Circuit Board 2S020-061 Used Working

Nikon Optistation 7 Circuit Board AF-CNT-KAB11110/3201-0 4S020-207-1 working

Nikon PCB Circuit Board SCPU 2S700-580-1 2S014-033-4

Nikon 4S018-870-B Circuit Board ALGMTH-X42 Rev C used working

PCB Circuit Board BSA-PZT Used Working

Nikon TCCNT 2S700-582-1 PCB Circuit Board 2S014-035-5 Used Working

Nikon 4S019-460 PCB Circuit Board BSA-MOT Used Working

Nikon 4S019-461 PCB Circuit Board BSA-OTH Used Working

The use of the product: