ABB Module 07NG61R1 ABB 07NG61-R1 07NG61 R1 Power Supply new version

ABB Module 07NG61R1 ABB 07NG61-R1 07NG61 R1 Power Supply new version

Product Description:

The trigger of the self-protecting mechanism is displayed by the red LED Ovl as long as the overload is present. In the PLC system an error message is then stored (FK4, error number 4). The open-circuit monitoring begins below ca. 3 mA. The value of the range underflow is stored. If the ope circuit monitoring is configured, the open-circuit event is displayed by the red LED Ovl as long as it is present. In the PLC system an error message is stored (FK4, error number 9). The following figure shows the connection of 2-pole passive- type analog sensors 4...20 mA. If the analog current sensors 4...20 mA are powered from a separate power supply unit, the reference potentials 0V (of the separate power supply unit and the power supply unit for the 07 KT 94) must be interconnected
to each other.In the above example, the AGND terminal remains
unused.

Related Product Recommendation:

Product's Character:

Input voltages that exceed the measuring range cause the overflow numerical value of +32767. If the measured value is below the range, the underflow numerical value Input currents that exceed the measuring range cause the overflow numerical value of +32767. If the measuredvalue is below the range, the underflow numerical value of -32767 is set. The input impedance is ca. 330 Ω. The current input has a self-protecting mechanism. If the input current gets too high, the shunt is switched off and the value for range overflow is generated. About every second, the unit tries to switch on the shunt again. In this way the correct measurement will succeed after the current has reached a normal value again.1 or 2 (see also the chapter "High-speed counter").Features of the analog inputs:The 8 analog inputs are not electrically isolated.The resolution of the A/D converter is 12 bits. Analog signals are conducted in shielded cables (seeThe analog inputs can be configured individually in a lot of different operating modes (even as digital inputs). The configuration is performed by setting certain bits in the system constants KW 86,00 to KW 86,07 as follows

FPR3330705R0321 ICBG32L7 Robot Coupler ABB
FPR3330705R0641 ICBG32L7 Robot Coupler ABB
FPR3331001R1202 ICSK20N1 I/O Remote Unit ABB Module ABB
FPR3331001R1204 ICSK20N1 I/O Remote Unit Module ABB
FPR3331001R1206 ICSK20N1 I/O Remote Unit Module ABB
FPR3335801R1012 ICST08A8 Analog Input Module - RTD ABB
FPR3335801R1014 ICST08A8 Analog Input Module - RTD ABB
FPR3335801R1016 ICST08A8 Analog Input Module - RTD ABB
FPR3335901R1012 ICST08A9 Analog Input Module - RTD ABB
FPR3335901R1014 ICST08A9 Analog Input Module - RTD ABB
FPR3335901R1016 ICST08A9 Analog Input Module - RTD ABB
FPR3341501R0044 ICSA04B5-120 Analog Output Unit - 120 V ABB
FPR3341501R0046 ICSA04B5-230 Analog Output Unit - 230 V ABB
FPR3341501R1042 ICSA04B5-24 Analog Output Unit - 24 Vdc ABB
FPR3345601R1012 ICSE08A6 Remote Analog Input Module ABB
FPR3345601R1014 ICSE08A6 Remote Analog Input Module ABB
FPR3345601R1016 ICSE08A6 Remote Analog Input Module ABB
FPR3346501R0014 ICSE08B5 Analog Input Remote Unit -120 VAC ABB
FPR3346501R0016 ICSE08B5 Analog Input Remote Unit 230 VAC ABB
FPR3346501R1012 ICSE 08 B5, ICSE08B5-24. ICSE08B5 Remote Analog Unit - 24 VDC ABB
FPR3350601R0064 ICSM06A6 Analog I/O Remote Unit ABB
FPR3350601R0066 ICSM06A6 Analog I/O Remote Unit ABB
FPR3350601R1062 ICSM06A6 Analog I/O Remote Unit ABB
FPR3471200R0006 NCB NCB Bus Amplifier ABB
FPR3471200R1002 CS31 Buss Repeater ABB
FPR3471300R0006 NCB NCB Bus Amplifier - Redundancy ABB
FPR3471300R1002 CS31-Repeater RS485 Module ABB
FPR3600201R0206 PLC Module ABB
FPR3600201R1202 PCZB PCZB Module ABB
FPR3600227R0204 07KR31 07 KR 31 Central Processing Unit -120 Vac ABB

FPR3600227R0206 07KR31 07 KR 31 Central Processing Unit- 230 vac ABB
FPR3600227R1202 07KR31 07 KR 31 Central Processing Unit 24VDC Input Power

The use of the product: