Allen Bradley Modules 1746-OA16 1746OA16 AB 1746 OA16 PLC OUTPUT High quality

Allen Bradley Modules 1746-OA16 1746OA16 AB 1746 OA16 PLC OUTPUT High quality

Product Description:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

Related Product Recommendation:

Product's Character:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

1746-A10 10-Slot Chassis AB
1746-A13 13-Slot Chassis AB
1746-A2 2-Slot Expansion Rack AB
1746-A4 4-Slot Chassis AB
1746-A7 7-Slot Chassis AB
1746-BAS BASIC Language Module AB
1746-BAS-T BASIC Language Module - High Speed AB
1746-BLM Blow Molding Module AB
1746-BTM Barrel Temperature Module AB
1746-C16 Chassis Interconnect Cable AB
1746-C9 Chassis Interconnect Cable AB
1746-FIO4I Fast Analog Input/Output Module AB
1746-FIO4V Fast Analog Input/Output Module AB
1746-HS Motion Controller Module AB
1746-HSCE High Speed Counter Module AB
1746-HSCE2 Multi-Channel High Speed Counter Module AB
1746-HSRV Servo Control Module AB
1746-HSTP1 Stepper Control Module AB
1746-HT Termination Panel AB
1746-IA16 120V AC Input Module AB
1746-IA4 120V AC Input Module AB
1746-IA8 120V AC Input Module AB
1746-IB16 Current Sinking DC Input Module AB
1746-IB32 Current Sinking DC Input Module AB
1746-IB8 Current Sinking DC Input Module AB
1746-IC16 Current Sinking DC Input Module AB
1746-IG16 Current Sourcing TTL Input Module AB
1746-IH16 Current Sinking DC Input Module AB

1746-IM16 240V AC Input Module AB
1746-IM4 240V AC Input Module AB
1746-IM8 240V AC Input Module AB
1746-IN16 24V AC/DC Input Module AB
1746-INT4 Thermocouple Input Module AB
1746-IO12 Combination Input/Output Module AB

The use of the product: