Allen Bradley Modules 1747-L541 1747 L541 AB 1747 L541 Processor/Controller For new products

Allen Bradley Modules 1747-L541 1747 L541 AB 1747 L541 Processor/Controller For new products

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Related Product Recommendation:

Product's Character:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

1772-CS Processor/Scanner Interconnect Cable AB
1772-LH Processor Interface Module AB
1772-LN2 CPU Module AB
1772-LP2 PLC-2/20 PLC-2/20 Processor Unit AB
1772-LP3 PLC-2/30 PLC-2/30 Processor Unit AB

1772-LS PLC-2/05 PLC-2/05 Processor AB
1772-LW PLC 2/17 MINI PLC 2/17 Processor AB
1772-LWP D PLC2 DNGL SL 6K Proc AB
1772-LX/C PLC 2/16 Mini PLC 2/16 Processor AB
1772-LX/D PLC 2/16 Mini PLC 2/16 Processor AB
1772-LXP Mini PLC 2/16 Processor AB
1774-MA 4 K Memory Module AB
1774-SD Remote I/O Module AB
1774-SR Remote I/O Half Scanner Module AB
1774-TB2 Interface Module AB
1775-A3 PLC-3/10 PLC-3 Chassis AB
1775-KA Communication Adapter AB
1775-L4 Main Processor Module AB
1775-MS4 Error Correcting Memory 16K Ram AB
1775-P2 Power Supply AB
1775-P3 Multi-Output Power Supply AB
1775-SR5 I/O Scanner Communications Module AB
1777-CP Terminator AB
1784-CP13 2801–N8 Video Interface Cable AB
1784-KT/B ISA/EISA Communication Module AB
1784-KTX ISA Communication Module AB
1784-PCICS PCI Bus Messaging Module AB
1784-PKTX/A PCI Network Interface Card - Series A AB
1784-PKTX/B PCI Network Interface Card - Series B AB
1785-ENET/A 96204473 Ethernet Interface Module AB
1785-KA Communication Adapter Module AB
1785-KA3 DH PLC-2 INTFC Communication Adapter Module AB
1785-L11B /11 /11 Processor Module AB
1785-L20B/C /20 /20 Processor Module - Series C AB
1785-L20B/E /20 /20 Processor Module AB

The use of the product: