Allen Bradley Modules 1756-LSP 1756LSP AB 1756 LSP ControlLogix Safety Partner NEW in sealed box

Allen Bradley Modules 1756-LSP 1756LSP AB 1756 LSP ControlLogix Safety Partner NEW in sealed box

Product Description:

All drives come equipped with a fault LED. When the fault LED is illuminated it is an indication a fault condition exists. Refer to page 2-3 for the location of the fault LED. Once the fault is properly cleared the LED will return to an off state. Diagnostics As can be seen in Figure 2.3, there are two indicators
provided to display the drive’s status condition. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive. The Fault Indicator is an LED that will be illuminated if a drive fault condition exists. Refer to details on How To Clear a Fault, below.How To Clear a Fault Important: Resetting a fault will not correct the cause of the fault condition. Corrective action must be taken prior to resetting the fault. To clear a fault perform one of the following:Cycle power to the drive. Cycle the stop signal to the drive. Cycle the [Clear Fault] parameter.

Related Product Recommendation:

Product's Character:

Two serial connectors to simplify RS-485 multi-dropping and host communications Several analog or digital command interfaces: Indexing (absolute with the Homing feature, incremental, or
registration)10 Volt analog interface—position, velocity, or torque control Presets (from one to eight binary inputs)—torque or velocity control Quadrature encoder digital interface—electronic gearing position follower Step/Direction digital interface—position control CW/CCW (step up/step down) interfaceposition control Operating mode override—alternate movement interface Host command digital interface The ULTRA 100/200 drives host command protocol provides optional drive configuration using the drive serial communications interface. This powerful feature allows your controller to access all of the drive digital controls using sequences of ASCII characters. The protocol includes error checking to
ensure the integrity of the transmitted commands. In installations that have multiple axes, up to 32 ULTRA 100/200 drives can be addressed by a host computer. These drives communicate with the host
computer using a four-wire RS-485 serial interface. The host command protocol includes specific drive addressing, which allows the host to communicate with all the connected drives concurrently.

1747-L531/D SLC 5/03 SLC 5/03 Control Processor AB
1747-L531/E SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/A SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/B SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/C SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/D SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/E SLC 5/03 SLC 5/03 Control Processor AB
1747-L541/B SLC 5/04 SLC 5/04 Processor - Series B AB
1747-L541/C SLC 5/04 SLC 5/04 Processor - Series C AB
1747-L542/A SLC 5/04 1747-L542 Processor - Series A AB
1747-L542/B SLC 5/04 1747-L542 Processor - Series B AB
1747-L542/C SLC 5/04 1747-L542 Processor - Series C AB
1747-L543/B SLC 5/04 Processor - Series B AB
1747-L543/C SLC 5/04 Processor - Series C AB
1747-L551/A SLC 5/05 SLC 5/05 Controller AB
1747-L551/B SLC 5/05 SLC 5/05 Controller AB
1747-L551/C SLC 5/05 SLC 5/05 Controller AB
1747-L552/A SLC 5/05 1747-L552 Processor - Series A AB
1747-L552/B SLC 5/05 1747-L552 Processor - Series B AB
1747-L552/C SLC 5/05 1747-L552 Processor - Series C AB
1747-L553/A SLC 5/05 Controller AB
1747-L553/B SLC 5/05 Controller AB
1747-L553/C SLC 5/05 Controller AB
1747-M1 1 K EEPROM Memory Module AB
1747-M11 Flash Memory Module - 32K AB
1747-M12 Flash Memory Module - 64K AB
1747-M13 64 K Flash EPROM Memory Module AB

The use of the product: