Allen Bradley Modules 1756-PLS 1756PLS AB 1756 PLS CONTROLLOGIX LIMIT SWITCH new version

Allen Bradley Modules 1756-PLS 1756PLS AB 1756 PLS CONTROLLOGIX LIMIT SWITCH new version

Product Description:

All drives come equipped with a fault LED. When the fault LED is illuminated it is an indication a fault condition exists. Refer to page 2-3 for the location of the fault LED. Once the fault is properly cleared the LED will return to an off state. Diagnostics As can be seen in Figure 2.3, there are two indicators
provided to display the drive’s status condition. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive. The Fault Indicator is an LED that will be illuminated if a drive fault condition exists. Refer to details on How To Clear a Fault, below.How To Clear a Fault Important: Resetting a fault will not correct the cause of the fault condition. Corrective action must be taken prior to resetting the fault. To clear a fault perform one of the following:Cycle power to the drive. Cycle the stop signal to the drive. Cycle the [Clear Fault] parameter.

Related Product Recommendation:

Product's Character:

Appendix B provides information about the Block Transfer messages supported by the Remote I/O communications module. In this appendix, you will read about the following: Block transfer status word.
Setting up data files for block transfer messages.Examples of block transfer messages. Block transfer quick reference. Important: This appendix provides detailed examples of block transfer messages. For information about block transfer messages, also refer to Chapter 5.Chapter 1 provides an overview of the
Remote I/O communications module (1203-GD1 module, 1203-GK1 module, and 1336-GM1 board). In this chapter, you will read about the following:Function of the module.Features of the module. Compatible SCANport products and programmable controllers. Parts and hardware of the module. Steps for setting up the module.Required tools and equipment.Description of the Remote I/O Communications Modules The Remote I/O communications module is an optional interface designed to provide a direct, digital link between an AB programmable controller and any one AB SCANport product. A module is required for each product that you want to connect to Remote I/O. There are three types of Remote I/O communications modules

1747-L531/E SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/A SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/B SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/C SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/D SLC 5/03 SLC 5/03 Control Processor AB
1747-L532/E SLC 5/03 SLC 5/03 Control Processor AB
1747-L541/B SLC 5/04 SLC 5/04 Processor - Series B AB
1747-L541/C SLC 5/04 SLC 5/04 Processor - Series C AB
1747-L542/A SLC 5/04 1747-L542 Processor - Series A AB
1747-L542/B SLC 5/04 1747-L542 Processor - Series B AB
1747-L542/C SLC 5/04 1747-L542 Processor - Series C AB
1747-L543/B SLC 5/04 Processor - Series B AB
1747-L543/C SLC 5/04 Processor - Series C AB
1747-L551/A SLC 5/05 SLC 5/05 Controller AB
1747-L551/B SLC 5/05 SLC 5/05 Controller AB
1747-L551/C SLC 5/05 SLC 5/05 Controller AB
1747-L552/A SLC 5/05 1747-L552 Processor - Series A AB
1747-L552/B SLC 5/05 1747-L552 Processor - Series B AB
1747-L552/C SLC 5/05 1747-L552 Processor - Series C AB
1747-L553/A SLC 5/05 Controller AB
1747-L553/B SLC 5/05 Controller AB
1747-L553/C SLC 5/05 Controller AB
1747-M1 1 K EEPROM Memory Module AB
1747-M11 Flash Memory Module - 32K AB
1747-M12 Flash Memory Module - 64K AB
1747-M13 64 K Flash EPROM Memory Module AB
1747-M15 Adapter Socket AB
1747-M2 4 K EEPROM Memory Module AB
1747-M5 Adapter Socket AB

The use of the product: