Allen Bradley Modules 11394C-AM04 AB 1394CAM04 1394C AM04 Controller Axis Module High quality

Allen Bradley Modules 11394C-AM04 AB 1394CAM04 1394C AM04 Controller Axis Module High quality

Product Description:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu.

Related Product Recommendation:

Product's Character:

All drives come equipped with a fault LED. When the fault LED is illuminated it is an indication a fault condition exists. Refer to page 2-3 for the location of the fault LED. Once the fault is properly cleared the LED will return to an off state. Diagnostics As can be seen in Figure 2.3, there are two indicators provided to display the drive’s status condition. The DC Bus Charge Indicator is a neon bulb that will be illuminated when power is applied to the drive. The Fault Indicator is an LED that will be illuminated if a drive fault condition exists. Refer to details on How To Clear a Fault, below.How To Clear a Fault Important:Resetting a fault will not correct the cause of the fault condition. Corrective action must be taken prior to resetting the fault. To clear a fault perform one of the following:Cycle power to the drive. Cycle the stop signal to the drive. Cycle the [Clear Fault] parameter.

1745-C2 Interconnect Cable AB
1745-C2 B Interconnect Cable, Series B AB
1745-C3 SLC 150 Interconnect Cable AB
1745-C3 A SLC 150 Interconnect Cable, Series A AB
1745-E101 Expansion Unit AB
1745-E102 Expansion Unit AB
1745-E103 Expansion Unit AB
1745-E104 Expansion Unit AB
1745-E105 Expansion Unit AB
1745-E106 Expansion Unit AB
1745-E107 Expansion Unit AB
1745-E151 SLC 150 Expansion Unit AB
1745-E152 SLC 150 Expansion Unit AB
1745-E153 SLC 150 Expansion Unit AB
1745-E154 SLC 150 Expansion Unit AB
C SLC 150 High Speed Input Module AB
1745-E156 SLC 150 Expansion Unit AB
1745-E157 SLC 150 Expansion Unit AB
1745-LP101 Processor Unit AB
1745-LP102 Processor Unit AB
1745-LP103 Processor Unit AB
1745-LP104 Processor Unit AB
1745-LP151 SLC 150 Processor Unit AB
1745-LP152 SLC 150 Processor Unit AB
1745-LP153 SLC 150 Processor Unit AB
1745-LP154 SLC150 SLC 150 Processor Unit AB
1745-LP156 SLC 150 Processor Unit AB
1745-LP157 SLC 150 Processor Unit AB
1745-M1-- EEPROM Memory Module AB
1745-PCC SLC Personal Computer Interface Converter AB

1745-PT1 Hand Held Programmer AB
1745-TCAT TCAT SLC-100 Timer Counter Access Terminal AB
1746-A10 10-Slot Chassis AB
1746-A13 13-Slot Chassis AB

The use of the product: