Allen Bradley Modules 1746-OAP12 1746OAP12 AB 1746 OAP12 Current Output Module Fast shipping

Product Description

Allen Bradley Modules 1746-OAP12 1746OAP12 AB 1746 OAP12 Current Output Module Fast shipping

Product Description:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

Related Product Recommendation:

Product's Character:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

1746-IO12 Combination Input/Output Module AB
1746-IO4 Combination Input/Output Module AB
1746-IO8 Combination Input/Output Module AB
1746-ITB16 Fast Response DC Sinking Input Module AB
1746-ITV16 Fast Response DC Sourcing Input Module AB
1746-IV16 Current Sourcing DC Input Module AB
1746-IV32 Current Sourcing DC Input Module AB
1746-IV8 Current Sourcing DC Input Module AB
1746-N2 Card Slot Filler AB
1746-NI16I High Resolution Analog Input Module - Current AB
1746-NI16V High Resolution Analog Input Module - Voltage AB
1746-NI4 High Resolution Analog Input Module AB
1746-NI8 High Resolution Analog Input Module AB
1746-NIO4I High Resolution Analog Input/Output Module AB
1746-NIO4V High Resolution Analog Input/Output Module AB
1746-NO4I Analog Current Output Module AB
1746-NO4V Analog Voltage Output Module AB
1746-NO8I Analog Current Output Module AB
1746-NO8V Analog Voltage Output Module AB
1746-NR4 RTD Input Module AB
1746-NR8 RTD Input Module AB
1746-NT4 Thermocouple Input Module AB
1746-NT8 Thermocouple Input Module AB
1746-OA16 120/240V AC Output Module AB
1746-OA8 120/240V AC Output Module AB

1746-OAP12 High Current 120/240V AC Output Module AB
1746-OB16 Current Sourcing DC Output Module AB
1746-OB16E Isolated Sourcing DC Output Module AB
1746-OB32 Current Sourcing DC Output Module AB
1746-OB32E Isolated Sourcing DC Output Module AB
1746-OB6EI Isolated Sourcing DC Output Module AB

The use of the product: