Allen Bradley Modules 1747-L542 1747 L542 AB 1747L542 New in Box Excellent Working Condition

Allen Bradley Modules 1747-L542 1747 L542 AB 1747L542 New in Box Excellent Working Condition

Product Description:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

Related Product Recommendation:

Product's Character:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

1785-L30B/A PLC -5/30 PLC -5/30 Processor - Series A AB
1785-L30B/C PLC -5/30 PLC -5/30 Processor - Series C AB
1785-L30B/D PLC -5/30 PLC -5/30 Processor - Series D AB
1785-L40B/C /40 /40 Processor Module - Series C AB
1785-L40B/D /40 /40 Processor Module - Series D AB
1785-L40B/E /40 /40Processor Module - Series E AB
1785-L40C15/E PLC -5/40 PLC -5/40 CONTROLNET Processor - Series E AB
1785-L40C15/F PLC -5/40 PLC -5/40 CONTROLNET Processor - Series F AB
1785-L60B PLC5/60 Processor Module AB
1785-L60B/C PLC -5/60 PLC -5/60 Processor - Series C AB
1785-LT/B Processor Module AB
1785-LT2 /25 /25 Processor Module AB
1785-LT4/A /10, 96077674 /10 Processor AB
1785-ME16 16K EEPROM Memory Cartridge AB
1786-TPYR ControlNet Tap AB
1791-8BC Block I/O Module AB
1792D-16BVT0D 95736401 1792DCBFM INPUT MODULE 16POINT SINK/SOURCE DEVICENET AB
1792D-8BVT0D 95705701 AB Top Input Unit 11-25VDC AB
1792D-CBFM base for: INPUT MODULE 8SINK/SOURCE 4CONNECTORS AB
1793-IB16 Digital Input Module AB
1793-IB16S Digital Input Module AB
1793-IB2XOB2P 24 VDC Combo Module AB
1793-IB2XOB2PS 24 VDC Combo Module AB
1793-IB4 Digital Input Module AB
1793-IB4S Digital Input Module AB
1793-IE2XOE1 Analog Combo Module AB
1793-IE2XOE1S Analog Combo Module AB
1793-IE4 Analog Input Module AB
1793-IE4S Analog Input Module AB
1793-IV16 Digital Input Module AB

The use of the product: