Allen Bradley Modules 1756-IB16I 1756 IB16I AB 1756IB16I DC Input Module Ship to Worldwide

Allen Bradley Modules 1756-IB16I 1756 IB16I AB 1756IB16I DC Input Module Ship to Worldwide

Product Description:

The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.

Related Product Recommendation:

Product's Character:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

1745-C2 Interconnect Cable AB
1745-C2 B Interconnect Cable, Series B AB
1745-C3 SLC 150 Interconnect Cable AB
1745-C3 A SLC 150 Interconnect Cable, Series A AB
1745-E101 Expansion Unit AB
1745-E102 Expansion Unit AB
1745-E103 Expansion Unit AB
1745-E104 Expansion Unit AB
1745-E105 Expansion Unit AB
1745-E106 Expansion Unit AB
1745-E107 Expansion Unit AB
1745-E151 SLC 150 Expansion Unit AB
1745-E152 SLC 150 Expansion Unit AB
1745-E153 SLC 150 Expansion Unit AB
1745-E154 SLC 150 Expansion Unit AB
C SLC 150 High Speed Input Module AB
1745-E156 SLC 150 Expansion Unit AB
1745-E157 SLC 150 Expansion Unit AB
1745-LP101 Processor Unit AB
1745-LP102 Processor Unit AB
1745-LP103 Processor Unit AB
1745-LP104 Processor Unit AB
1745-LP151 SLC 150 Processor Unit AB
1745-LP152 SLC 150 Processor Unit AB
1745-LP153 SLC 150 Processor Unit AB
1745-LP154 SLC150 SLC 150 Processor Unit AB
1745-LP156 SLC 150 Processor Unit AB
1745-LP157 SLC 150 Processor Unit AB
1745-M1-- EEPROM Memory Module AB
1745-PCC SLC Personal Computer Interface Converter AB

1745-PT1 Hand Held Programmer AB
1745-TCAT TCAT SLC-100 Timer Counter Access Terminal AB
1746-A10 10-Slot Chassis AB
1746-A13 13-Slot Chassis AB
1746-A2 2-Slot Expansion Rack AB

The use of the product: